Weld On "DB3" Rear Control Arm Correction Bracket, Jeep JK Wrangler
The MetalCloak Jeep JK Weld On "DB3" Rear Control Arm Correction Bracket System is the best solution to convert your long arm system back to a mid arm set up.Features Include:
- Fits JK Wranglers
- 3/16" Steel
- CAD Designed
- Laser Cut
- Ready To Be Welded
- Fixture Spacers Included
- Angled for Approach & Departure
- Trail-Tested Built-In Skid Plate
- Raw Metal Finish
- Made in the USA
The Weld-On DB3 welds directly to the stock location of the factory rear control arm frame brackets that were cut off when installing a long arm kit. The weld on DB3 allows you to fully weld the bracket to the frame and is angled for approach and departure when off-roading. The weld on DB3 comes with fixture spacers that allow you to adjust the parts perfectly to the frame so you know the bracket is aligned when welding.
Feel the improvement in acceleration, braking, climbing and steering performance with the DB3. The DB3 is only available from MetalCloak.
Note: This alignment bracket is designed to be used with Adjustable rear control arms. Not to be used with stock control arms.
Note: This is a weld-on DIY product. Do not purchase this product unless you are prepared to weld onto your Jeep.
Note: Builder Parts are intended for your own custom application. There is no implied warranty or instructions for the use of these products; if using any of the builder parts you should be confident of your mechanical skill level and know that you will use at your own risk.
[click for less...]
MetalCloak's Jeep Wrangler Suspension.
Who Is MetalCloak?
MetalCloak creates Game-Changing Products for the Off Road Enthusiast.
What is Corner Travel Index?
Since 2014 MetalCloak has tested thousands and thousands of rigs at events all across the county collecting specs on the build and cataloging the results. The data collected allows us to make our own products better.
FMVSS 126 Compliant
MetalCloak not only has the best off road flex, but we are also Federal Motor Vehicle Safety Standard 126 certified and compliant. No other company can match our on- and off-road performance.
Proudly Made in the USA
MetalCloak proudly manufactures products in America. Take a glimpse of Our incredible team that lives and breaths innovation and quality.
Rear Control Arm Correction Bracket "DB3"
Green line shows DB3 and how it tucks behind wheel for optimal approach.
Red line shows a "typical" Long arm hang up MUCH farther forward increasing the chance for hang up.
The DB3 provides superior control arm angles for a better ride AND provides better approach angles over a rear long arm all in a simple bolt on application.
Correction Bracket Geometry
This product adjust the roll center of your Jeep, and corrects the geometry of the control arms enabling the full use of up and down travel.
The entire DIY bracket assembly gets welded together for incredible strength, has built in approach skids, and all surfaces are angled to keep from catching on obstacles. Installs where the factory control arm mounts were located.
Fixture Alignment Spacers
The weld-together weld on DB3 comes with fixture spacers that allow you to adjust the parts perfectly to the frame so you know the bracket is aligned when welding.
What Does It Do?
Adding this system improves rear control arm geometry and adjusts rear axle caster for lifted JK Wranglers. The flatter the control arms are the better; the benefits are immediately felt with a smoother ride and stable handling as the roll center has been adjusted. Braking performance also improves maximizing safety along with the comfort and performance of your Jeep JK Wrangler.
What's In The Kit?
- DB3 Correction Bracket
- Bracket Spacers
- All Required Hardware
|Compatibility||2007 - 2018 JK Wrangler|
|Drop Bracket||3/16" Steel Sheet|
Control Arms: This alignment bracket is designed to be used with Adjustable rear control arms. Not to be used with stock control arms.
Weld On Product: This is a weld-on product. Do not purchase this product unless you are prepared to weld onto your Jeep.
Builder Parts: Builder Parts are intended for your own custom application. There is no implied warranty or instructions for the use of these products; if using any of the builder parts you should be confident of your mechanical skill level and know that you will use at your own risk.
This product is considered a Builder's Part. As such we do not provide the typical comprehensive instructions that MetalCloak is known for.
Please do not purchase this product unless you either have the full confidence to install this product yourself, or are prepared to have a professional do it.
If you have any questions about the difficulty of the installation of this product, please call us at 916-631-8071.